Cold storage board manufacturers tell you what is the installation process of cold storage board?

Cold storage board manufacturers tell you that the installation of cold storage board wallboard should start from the corner. According to the ship plate diagram, transport the two plates at the corners that need to be installed to the installation site, and drill holes in the middle of the plate width according to the angle iron part model of the fixed plate height and mushroom head nylon bolts. The drill bit should be perpendicular to the plate, and the mushroom head nylon bolt (nylon bolt and cream sealed in the mushroom head) should be worn in the hole, and the angle iron parts should be tightened, and the library plate should be tightened. When erecting the wallboard, soft materials such as foam shall be laid in the floor trough in contact with the warehouse board to prevent the warehouse board from being damaged. After the wallboard at two corners is neutral in the floor trough, the plane position of the wallboard and the verticality of the warehouse board shall be adjusted in time according to the position of the placement line.

In addition, make sure that the top height of the wall panel is correct (always need to check). If the position of the wall plate is correct, weld the angle iron to the plate beam and fix the inner outer cover angle (put a sealing ointment on the inner side of the angle plate where it contacts the library plate). When welding angle iron parts, the original angle iron parts should be covered with a shield to prevent the high-temperature baking plate and welding residue from splashing on the steel plate during arc welding.

The cold storage board manufacturer tells you that after the cold storage board is installed at the corner of the two wall panels, the next wall panel will be installed along the corner. Before installing the next wallboard, apply two white sealing paste on the floor (the sealing paste needs to match the convex shape or groove angle of the library board). The sealing paste in the convex groove or groove shape needs to have a certain height and be installed tightly and evenly in the same way as the first wallboard.

The cold storage board manufacturer tells you that the cold storage board is between the two library boards. First, hit the square wood spread on the polyurethane library board with a hammer, close to the board and between the boards. There are two sets of connectors between the wallboard and the wallboard fixed with wedges. The two sets of connectors are respectively fixed on the upper and lower parts of the gap between the wallboard and the wallboard. The connectors inside the lower part need to be as downward as possible so that the concrete can cover the connectors. The gap between the board and the board should remain approximately 3mm wide after tightening with the connector wedge. For example, if it does not meet the core requirements, you need to remove the board, refine the edge of the board, and then reinstall it to make the board gap meet the requirements. When fixing the connector, it is recommended to fix the two parts of the connector group on the edges of the convex and concave library plates respectively, and fix them with 5X13 rivets. The connector distance will tighten the two library plates. When the wedge is firmly wedged, the hammer should be kept perpendicular to the wedge to avoid hitting the steel plate. The upper and lower parts of the wedge should be tightened at the same time, and the wedge should be fixed with rivets.

Cold storage board manufacturers tell you what is the development status of cold storage board?

Therefore, the renewal of refrigeration technology. The tentacles of the freezer project have penetrated into more areas. In chemical raw materials, pharmaceuticals, scientific research, cold drinks, flowers, green plants, tea, medicine, electronic instruments, mushroom cultivation, air conditioning warehouse, logistics and other aspects of development. The deeper the tentacles of refrigeration technology in various fields, the more the number of refrigerated warehouses. The increase in the number of freezers has brought about an increase in the demand for freezers. According to the "Refrigeration Express" reporter, China's demand for refrigeration and refrigeration is rising at a rate of 30% per year. This is a great opportunity for refrigerated plate enterprises. It also indicates that our cold storage and freezing industry is gradually improving. The construction of cold storage in all parts of our country is in full swing, which undoubtedly provides many opportunities for the development of cold storage enterprises in our country. Many enterprises cater to the opportunity and begin to grow and expand rapidly. Therefore, with the vigorous development of the freezer industry, many companies have also joined the freezer manufacturing and production business. Competition among freezer companies is also growing. As a result, strong enterprises have become stronger, and the space for weak enterprises to survive is shrinking. Quality and price become the competition between freezer enterprises.